How to make a six-pointed origami star
six-Pointed Origami Star: try all 18 steps in the 3D player. Turn and replay every move. Print the complete diagram sheet or save it as PDF.
A six-pointed star made of six identical bars, each one square folded in half three times. The bars cross as two triangles, and every point is closed with a hooked end, so the star needs no glue.
- You need
- Six equal squares of thin origami paper, three of each color. No glue or scissors.
- Start
- Take six squares of the same size, three gold and three silver. Set them in two columns of three, gold on the left and silver on the right, all with the same side up.
- Tips
- Crease each fold sharply so the bar stays narrow and even.
- Lay each bar so its ends reach two points of the star.
- Hook one point at a time and press it flat before the next.
Your model is ready
Six bars cross as two triangles and each of the six points is hooked shut. Press the points flat. The finished six-pointed star, gold and silver bars crossing at six points.
Step-by-step diagrams
Steps 1–7
- 1
Fold the left squares in half
Fold the left edge of each left-hand square over to its right edge, and press.
- 2
Fold the right squares in half
Fold the right edge of each right-hand square over to its left edge, and press.
- 3
Fold the left bars in half again
Fold the left edge of each left-hand bar over to its right edge again, and press.
- 4
Fold the right bars in half again
Fold the right edge of each right-hand bar over to its left edge again, and press.
- 5
Fold the left bars in half again
Fold the left edge of each left-hand bar over to its right edge again, and press.
- 6
Fold the right bars in half again
Fold the right edge of each right-hand bar over to its left edge again, and press.
- 7
Lay down bar 1
Lay bar 1 where the drawing shows.
Steps 8–14
- 8
Lay bar 2 under the others
Slide bar 2 under the bars already down and turn it into its place in the star.
- 9
Lay bar 3 under the others
Slide bar 3 under the bars already down and turn it into its place in the star.
- 10
Lay bar 4 under the others
Slide bar 4 under the bars already down and turn it into its place in the star.
- 11
Lay bar 5 under the others
Slide bar 5 under the bars already down and turn it into its place in the star.
- 12
Lay bar 6 under the others
Slide bar 6 under the bars already down and turn it into its place in the star.
- 13
Hook bar 1 behind bar 3
Fold the end of bar 1 back behind bar 3, round its edge. The point now holds bar 3.
- 14
Hook bar 1 behind bar 5
Fold the end of bar 1 back behind bar 5, round its edge. The point now holds bar 5.
Steps 15–18
- 15
Hook bar 2 behind bar 4
Fold the end of bar 2 back behind bar 4, round its edge. The point now holds bar 4.
- 16
Hook bar 2 behind bar 6
Fold the end of bar 2 back behind bar 6, round its edge. The point now holds bar 6.
- 17
Hook bar 3 behind bar 5
Fold the end of bar 3 back behind bar 5, round its edge. The point now holds bar 5.
- 18
Hook bar 4 behind bar 6
Fold the end of bar 4 back behind bar 6, round its edge. The point now holds bar 6.
- ✓
Finish
Six bars cross as two triangles and each of the six points is hooked shut. Press the points flat. The finished six-pointed star, gold and silver bars crossing at six points.
Fold next
Paper lantern ↗
The traditional flat paper lantern, with a wide middle and two rectangular ends. The same fold was called a muff or short-sleeved shirt in European kindergarten books.
Star ↗
An Origami Tutor eight-pointed star made from eight equal folded triangles. Every gold point is long and sharp, with a deep notch between its neighbours. Three folds make each ray; a little glue holds their overlapping bases together.
Paper Christmas tree ↗
An accordion Christmas tree with a pointed top, broad base and six pleated panels. Cut a triangle from a green rectangle, fold the pleats and open them into a zigzag decoration.
Christmas tree ↗
An Origami Tutor Christmas tree with three stepped tiers and a short trunk. Folded from one square of green paper with a kite fold and two pleats; no cuts or glue.